How to turn a wireless card into an AP
There are several steps to turn a wireless card into an AP.
1, plug the wireless card, install the prompted driver, open the configuration program;
2, click the last configuration, in the AP mode click “on”, click OK;
3, set all the options, and then click Apply;
4, click the local connection, and then click Properties, select Advanced Options in Properties, and then click “Allow APs”. local connection, then click Properties, select Advanced Options in Properties, then click “Allow other network users to pass through this computer’s Internet link”, click OK.
What does wireless card AP mean? How does it work?
AP is wireless access point.
Wireless AP is a wireless access point, which is used as a wireless switch for a wireless network and the core of a wireless network. Wireless AP is the access point for mobile computer users to access the wired network, which is mainly used in broadband home, inside the building and inside the campus.
Can cover tens to hundreds of meters. Wireless AP is a very wide range of names, it contains not only simple wireless access points, but also wireless routers and other types of equipment.
Function:
An important function of the AP is the relay, the so-called relay is between the two wireless points to amplify the wireless signal once, so that the remote client can receive a stronger wireless signal.
For example, if you place an AP at point a, and there is a client at point c, there is a distance of 120 meters between them, and the signal from point a to point c has been weakened a lot, so in the middle of the 60-meter point b to put an AP as a relay, so that the client’s signal at point c can be effectively strengthened, to ensure that the transmission speed and stability.
Win7 system using usb wireless card to set up wireless sharing when prompted to simulate the AP configuration failure of the solution
Many users will be through the wireless card to use the wireless network, in order to facilitate the use of multiple people to use the wireless network, the wireless network is usually shared, however, recently there are users in the use of usb wireless card to set up wireless sharing when prompted to simulate the AP configuration failure, please Ensure that the system InternetConnectionSharing (ICS) and WindowsFirewall services have been turned on.” This tutorial will share with you the solution to the problem of prompting analog AP configuration failure when setting up wireless sharing using a usb wireless card on the Win7 system.
Mainly due to the system several key services are not open, the solution is as follows:
1, right-click on the desktop “my computer” (computer), click on “Management”, enter the computer management page;
2, expand the desktop “my computer” (computer), click on “Management”, enter the computer management page;
2, expand the “Services and Applications” list, click “Services”;
3, in the right-hand service list column, respectively, select “WindowsFirewall “and” InternetConnectionSharing (ICS) “service (Win8.1 system only need to open the ICS service), right-click and select Properties, will be” Startup Type
4. Click “Start this service” to ensure that the service can be started successfully.
If you fail to start the service, you need to check the reason why you fail to start the service, sometimes it is caused by antivirus software, you can quit or uninstall it and try again.
On the Win7 system using a usb wireless card to set up wireless sharing prompted by the analog AP configuration failed to solve the problem, if you have encountered the same situation, you can take the above method steps to operate it.
In winxp under the wireless network card as APWIFI sharing to cell phones or laptops method
1. plug their wireless network card, and then start the menu to run in the input ncpa.cpl into the local connection properties, select the advanced Internet connection sharing point check, and then determine. 2.point wireless network properties select wireless network configuration enter SSIDtest,network identity is open,encryption is disabled,advanced options for computer to computer. . 4. Refresh the network list appears test access point ssid. 5. Connect test access point. 5. 5. Open your cell phone to search for test, and then connect. dhcpip for 192.168.0.xx network segment. 6. test connected successfully as follows: Note: When test is connected, then use your cell phone to search for test, and then connect until you get the ip address. Next time will not automatically connect, to manually connect.